Concrete testing instrument
Cement, cement slurry test equipment
Mortar test instrument
Asphalt test equipment
Asphalt grease test equipment
Universal, pressure, testing machine series
Geotechnical test equipment
Constant temperature and humidity curing instrument
Electronic balance, test mode series
Subgrade, pavement, field testing instruments
CA mortar instrument
Geosynthetics testing instrument
Nondestructive testing equipment
Linoleum, waterproof coil test equipment
Rock aggregate, tunnel test instrument
Building energy saving. Insulation material testing instrument
Brick / Brick Ceramic Instrument Series
Glass, energy-saving testing equipment
Anti-bending, anti-compression, anti-split fixture series
Longer series
Tianjin Huatong Experimental Instrument Factory Contact: Manager Wang Sales Tel: 022-27361556
Sales Phone: 022-27641869
Mobile: 13502140666
Address: Sanyuancun Street, Nankai District, Tianjin
Universal, pressure, testing machine series
Position-> Home > Products > Universal, pressure, testing machine series > YFXGW-40A vertical steel bar reverse bending test machine

YFXGW-40A Vertical Reverse Bend Testing Machine



YFXGW-40A vertical steel bar reverse bending test machine <br /> I. Introduction :
The steel bar bending tester is a special equipment for cold bending test and flat and reverse bending test of steel bars. Its main technical parameters are in accordance with GB / T1499.2-2018 "Plan for Reverse Plane Bending Test of Steel Bars" and ISO10065: 1900 regulations and requirements related to cold bend test and plane reverse bending test. This equipment is the ideal testing equipment for steel plants and construction units to inspect the bending performance of steel bars.
The steel bar bending tester has the characteristics of compact structure, simple operation, intuitive bending angle display, easy maintenance, stable operation, safety and low noise.
This machine applies to the following standards:
--GB / T232-2010 《Metal material bending test method》
--GB / T1499.2-2017 "Steel for reinforced concrete Part 1: Hot-rolled round bar"
--GB / T1499.2-2018 "Steel for reinforced concrete Part 2; Hot-rolled ribbed steel"
--GB / T28900-2012 steel test method for reinforced concrete;
--GB / T21839-Test method for steel for prestressed concrete;
--GB / T1499.3-2010 "Steel for reinforced concrete Part 3; Welded wire mesh for reinforcement"
--GB / T13014-2013 residual heat treatment steel bars for reinforced concrete;
--GB / T13788-2017 《Cold-rolled ribbed steel bar》
--YB / T5126-Test method for bending and reverse bending of steel for reinforced concrete;
--GB / T33279-2017 Rebar for track board
Second, the scheme description <br /> The working principle of the testing machine: using digital integrated circuits, the bending angle of the testing machine is divided by the photoelectric pulse obtained from the support roller shaft, the angle is counted and continuously displayed, when the testing machine When the work roll is turned to the set angle, it is controlled by the logic circuit to make the solenoid valve control the oil circuit. In order to ensure the safety of the operator and the equipment, the equipment is also equipped with a reliable limit mechanism, which can stop the equipment in time when the electrical control part is out of control or misoperation.
Third, installation <br /> Install on a stable basis, the horizontal flatness error should not be greater than 0.5 / 1000; the power supply is a three-phase four-wire 380V / 220V, 50HZ power supply.
Fourth, the structure introduction <br /> This steel bending tester consists of the following parts:
1. Frame; 2. Workbench; 3. Working support roller; 4. Hydraulic oil cylinder; 5. Hydraulic oil pump (including motor); 6. Electrical part; 7. Accessory part
V. Technical parameters <br /> Maximum diameter of bending steel bar Bending circle sample diameter: 400 / 400E: φ6-φ40mm
500 / 500E / 600: φ6-φ32mm
Forward bending angle: arbitrarily set within 0-180 Reverse bending angle: arbitrarily set within 0-90 Working cylinder working speed: 300mm / min
Motor power: 1.1kw
Machine appearance (mm): 850 * 650 * 2000mm
Machine weight: 700kg
Six, equipment parameters and main configuration
Equipment parameters
1.1 Maximum thrust: 300kN
1.2 Roller width: 0 ~ 400㎜
1.3 Roller diameter: Φ50㎜
1.4 Minimum rebar diameter: Φ6㎜
1.5 Maximum rebar diameter: Φ40㎜
1.6 Maximum bending angle: 180
1.7 Cylinder diameter: Φ110㎜
1.8 Piston stroke: 360㎜
1.9 No-load propulsion speed of piston: about 260㎜ / min
1.10 Hydraulic oil volume: about 38 L
1.11 hydraulic oil brand: L-HM46 hydraulic oil or equivalent hydraulic oil
1.12 Working pressure of hydraulic system: 16MPa
1.13 Host power supply: AC three-phase five-wire 380V 10% 50Hz 1.5kW
2. Main equipment configuration:
2.1 one host
2.2 an open-end wrench
2.3 Core diameter is 3, 4, 5, 8, 10, 12, 14, 16, 16.5, 18, 20, 21, 24, 25.5, 30, 31.5, 32, 36, 40, 42, 44, 48, 50 , 54, 56, 60, 64, 66, 72, 75, 80, 88, 100, 112, 128, 140, 144, 160, 180, 200 each. One core bracket {3-10}, {12-18}, {18-30}, {30-50}, {50-60}, {60-80} (matched with each core).
Performance advantages of our products
1. The bending angle of our company's bending testing machine is the angle obtained by real-time tracking of the encoder, so the angle can be guaranteed from 0 to 180 , and the angles are all standard. However, the bending angle of other bending testing machines is calculated according to the triangle geometry theorem, and the angle will have errors.
2. The bending tester of other homes needs to install a special support for the reverse bending test, and the weight of that support is sixty to seventy kilograms, which is very inconvenient for loading and unloading.
3. The bending testers of other homes need to hold the rebar first when they do reverse bending. Only when the upper indenter touches the test rebar, they can leave their hands. The danger factor is relatively high.
4. Your organization can ask other homes for a non-reduced version of the bending test machine operation video, then it can be clearly seen that his type of operation is very inconvenient.
Unknown Views: Print this pageClose window
Back to Home   |   company profiles   |   Products   |   news   |   technical article   |   Instrument software   |   Integrity Archive   |   Online message   |   contact us
Copyright ? 2002-2011 Tianjin Huatong Experimental Instrument Factory All rights reserved Jin ICP No. 12005878-1
Security Alliance